Pond Pumps Canada is part of the Amazon Affiliate Network. We may receive payment for items purchased through the Amazon website.

The AAPA45L is perfect to run several Waterfarms or multiple air stones at once. It is an electrical magnetic air compressor in a high-quality aluminum alloy case, that is made with wear and tear resistant material for its cylinder and piston, and boasts high pressure and high output. The AAPA45L comes with multi-outlet divider (6, 8, and 12) that can be individually opened or shut. The AAPA45L Commercial Pond Air Pump comes in at 45 LPM watts, has a GPH of 700, and has a total of 6 outlets. The Active Aqua Hydrofarm AAPA45L 45 LPM Commercial Air Pump is an ideal choice for pond and growing projects that need a powerful energy source to keep running and thriving efficiently for long periods of time.
  • Perfect to run several waterfarms or multiple air stones at once
  • High pressure and high output; comes with multi-outlet divider
  • Super silent with multi-level muffler
  • Special artificial rubber to keep a steady air flow output and pressure that can be adjusted freely
  • 700-gph, maximum amperage is 0.17 and maximum decibels is 45

Write a review

Note: HTML is not translated!
    Bad           Good

Hydrofarm AAPA45L 20-Watt 45-LPM Active Aqua Commercial Air Pump with



Related Products

Hydrofarm AAPW400 400-GPH Active Aqua Submersible Pump

Hydrofarm AAPW400 400-GPH Active Aqua Submersible Pump

Active Aqua, 400 GPH, Submersible Water Pump, Built To Go Be..

Hydrofarm AAPW550 550-GPH Active Aqua Submersible Pump

Hydrofarm AAPW550 550-GPH Active Aqua Submersible Pump

The 550 GPH Active Aqua Submersible Pump was built to go bel..

Hydrofarm ASCL Large Active Aqua Air Stone Cylinder

Hydrofarm ASCL Large Active Aqua Air Stone Cylinder

About Hydrofarm, Inc. Celebrated as the nation's oldest and ..

Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.