Pond Pumps Canada is part of the Amazon Affiliate Network. We may receive payment for items purchased through the Amazon website.

  • Flojet 18555000A Waste Water Pump
Portable RV Waste PumpThe Flojet 18555-000 DC portable waste pump is the ideal solution for emptying holding tanks on recreational vehicles and avoiding dump stations. The macerator section grinds waste down to a particle size of ⅛" maximum so it can easily be pumped through a garden hose (⅝" minimum). The pump section is self-priming, permitting the unit to be mounted above the tank in a convenient location.Empties most recirculating toilets in less than 2 minutes; empties a typical 30-gallon holding tank in less than 3 minutes.The 18555-series waste pump will macerate and pump all waste and tissue normally found in recreational vehicle waste systems. IT WILL NOT HANDLE HARD SOLID OBJECTS, SANITARY NAPKINS OR RAGSConnects directly to the RV waste outletEliminates 3" (75mm) sewer hoseGarden hose discharge portFresh water rinse capabilitiesRemote handheld on/off switch with 6' (1.8M) wire harnessAbility to dump longer distancesAbility to drain holding tanks at homeEasy clean up and storageRugged portable storage caseUSCG and CSA listedRun dry protection
  • Easy clean up and storage
  • Plastic storage case included
  • Run dry protection
  • Ability to drain holding tanks at home
  • Minimal user contact with waste

Write a review

Note: HTML is not translated!
    Bad           Good

Flojet 18555000A Waste Water Pump

  • Brand: Flojet
  • Product Code: 18555000A
  • Availability: In Stock

Related Products

Amarine-made 12V 45 LPM 12GPM Quick Release RV Mount Macerator Waste Water Pump,Boat RV Marine

Amarine-made 12V 45 LPM 12GPM Quick Release RV Mount Macerator Waste Water Pump,Boat RV Marine

FEATURES:-Macerator pump combines a self-priming flexible im..

Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.